LM3406 LED DRIVER

Yes, you must use the other components in the circuit diagram. There’s a circuit diagram in the datasheet that calls for a number of other components. Since I want to be able to run these at different currents, and several of the calculations call for the current, should I run the numbers for each of the 3 currents I’m planning on, and then get a part that would satisfy the worst case scenario? I want to have the option to drive them at capacity for adaptability of the lighting unit. The product detailed below complies with the specifications published by RS Components. Anyway, I put a big 12 Ohms resistor in the white lines actually, I am not sure about the value and cannot have a look right now, but there is a resistor!

Uploader: Gozshura
Date Added: 8 April 2013
File Size: 43.17 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 7672
Price: Free* [*Free Regsitration Required]

I would like to preface this post with stating that I am pretty new to the world of electronics.

The simplicity is that there are always 3 LEDs in a row. Pay special attention to lk3406 a suitable inductor, as shown on pages Hopefully, my last stupid question.

Texas Instruments LM3406MHEVAL/NOPB, 1.5 A LED Driver Evaluation Board for LM3406

If not are there any other more cost effective solutions? I would also need to be able to dim each color individually. No, do NOT add any resistors in series. I find that that pin is left open in input voltage comparator for PWM dimming.

  ALC862 ATI SB450 DRIVER DOWNLOAD

Save to an existing parts list Save to a new parts list. This minimizes the response time needed to turn the LED array back on. So far my plan is to drive them with an lm with the LEDs in series strings of 4, which would mean I would need 5 lm ics. Sign up or log in Sign up using Google. For cooling the LEDs I mounted pm3406 on aluminum blocks and those onto a stainless steel tube.

Yes, you must use the l,3406 components in the circuit diagram. Since I’d be PWM dimming them, the duty cycle would vary based on whatever brightness happens to work lm34406 it would change as they are fading on and off.

What is high power Led actually.

It uses a diode and a capacitor to smooth the input, and allow it to dim that way. If the psu is lmm3406 12 volts, and the string doesn’t dissipate the full 12 volts, would I need to add a resistor in line with the LEDs, or would throttling it down with pwm be enough protection? Sign up using Facebook. The Manufacturers reserve the right to change this Information at any time without notice.

lm4306

Controlling led array with Arduino with LM

Save to parts list Save to parts list. This particular one did list part numbers, but as I said most are no longer stocked. Home Questions Tags Users Unanswered.

Or would there be other advantages to driving at lower currents for lower brightness? Also, do I need any extra hardware to drive the LEDs with the lm? Would I need to heatsink the LM’s if they get an input voltage of say 12, but are only outputting like 4.

  15 TFT LCD MONITOR 710A DRIVER DOWNLOAD

Since I want to be able to run these at different currents, and several of the calculations call for the current, should I run the numbers for each of the 3 currents I’m planning on, and then get a part that would satisfy the worst case scenario? Add to a parts list.

Therefore these may be stupid questions. What value should I use for D? lfd

Driving W LEDs with lm

There’s a circuit diagram in the datasheet that calls for a number of other components. To determine whether you will need a heatsink, calculate the temperature rise as shown lm306 page 27 of the datasheet.

You agree that the Information as provided here through an intermediary may not be error-free, accurate or up-to-date and that it is not advice.

Please select an existing parts list. You have chosen to save the following item to a parts list:. Can I rephrase it 8.